Mazda CX-30: How to switch on the wiper deicer
The equipped windshield wiper de-icers operate together with the rear-window defogger.
YOUR CAR · Mazda
48 practical answers. Each article identifies the manual, market and equipment covered.
Search these guides →The equipped windshield wiper de-icers operate together with the rear-window defogger.
Select AUTO on an equipped wiper lever and adjust sensitivity with its ring.
The rear control selects intermittent wiping, continuous wiping or stop.
Start the engine and center a compatible Qi phone on the tray.
Switch vehicle power ON then OFF, and move the lever to MIST twice within 30 seconds.
Warm the engine, stop on level ground and wait at least five minutes.
Add suitable windshield washer fluid when the level is low, below the equipped E mark, or a low-fluid warning appears.
With the engine cool, coolant should lie between the reservoir FULL and LOW marks.
Check that brake fluid is between MIN and MAX.
Check the tires monthly while cold, including the temporary spare.
The key battery is beneath the transmitter covers and inner cap.
Press the brake, align the center of the key emblem with the center of the start button, and wait for a steady green indicator before pressing the button.
Remove the auxiliary key from the transmitter and insert it into the driver-door lock while pulling the handle.
If a key has been temporarily suspended because it was left inside the car, press unlock on that suspended key inside the vehicle to restore its functions.
With vehicle power ON, adjust the driver seat, outside mirrors and equipped display.
Stop the powered liftgate above halfway at the desired height and hold its close switch at least three seconds.
With the vehicle stopped and power OFF, hold the key’s liftgate button at least one second.
With vehicle power ON, fully open the affected window, close it fully and keep pulling its switch for about two seconds after closure.
Press the window-lock switch on the driver door to disable the passenger and rear-seat window switches.
With power ON, press the roof switch to tilt or move it rearward to slide.
Start the engine and use the seat-warmer switch to cycle its temperature.
Enable Occupant Comfort and press climate AUTO to let equipped front seat heating respond to cabin conditions.
On an equipped CX-30, start the engine and press the heated-wheel control.
With vehicle power in ACC or ON, select the mirror side, adjust its angle, then press the same selector again so its indicator turns off.
Use the dashboard illumination plus and minus controls.
Press TRIP to select the trip record and hold TRIP for at least two seconds to reset it.
Show average fuel economy and hold INFO for at least two seconds.
Use Mazda Connect Settings to change the equipped active driving display.
Start the engine and press the rear-window defogger switch.
On equipped vehicles, the mirror defoggers work together with the rear-window defogger.
The USB power outlets work with vehicle power in ACC or ON.
The equipped 12-volt accessory socket supplies power with vehicle power in ACC or ON.
Switch power OFF, unlock the driver door and press the fuel-filler lid.
Pull the interior release, release the secondary latch and support the hood using its rod.
Press AUTOHOLD for standby, then brake to a complete stop.
With the engine running, driver door closed and brake firmly depressed, shifting from P can release the parking brake.
Sport mode can be unavailable while ABS, traction control, stability control or radar cruise are operating, or during abrupt steering.
Start the engine, press AUTO and set the desired temperature.
Press the windshield-defroster switch on the automatic climate panel.
Detach the cover straps from their liftgate hooks, lift the cover near its locating pins and remove its front end for more luggage space.
Vacuum grit, clean with a suitable leather product or about 5% mild-detergent solution, wipe away detergent and allow the leather to dry in shaded ventilation.
Clean belt webbing gently with mild detergent, wipe with a well-wrung cloth and let it dry.
Rinse seawater or road de-icing residue off the wheels promptly.
Wipe the active-driving-display dust sheet with a fine, soft eyeglass-style cloth.
Open each rear door and use the auxiliary key to turn its child-safety lock to the lock position.
If addressing a dead vehicle battery does not restore the liftgate, use its interior emergency access cover and release lever.
On an Alexa-equipped CX-30, check the Amazon sign-in and Alexa Hands-Free setting.
If the active driving display stops operating, safely switch vehicle power OFF and restart the engine.