Mazda CX-5: How to adjust automatic wiper sensitivity
Select AUTO on a rain-sensor-equipped car and rotate the wiper-stalk sensitivity ring.
YOUR CAR · Mazda
52 practical answers. Each article identifies the manual, market and equipment covered.
Search these guides →Select AUTO on a rain-sensor-equipped car and rotate the wiper-stalk sensitivity ring.
Use the rear wiper ring on the wiper stalk.
On equipped vehicles, the windshield wiper de-icer runs together with the rear-window defogger.
Place a compatible Qi phone centrally on the charging tray with the engine running and all doors and liftgate closed.
The USB power outlets described in this section are charging-only.
Before replacing streaking blades, clean the glass and blade surfaces with a suitable cleaner or mild detergent, then rinse thoroughly.
Check the dipstick on level ground after warming the engine, switching it off and waiting at least five minutes.
The front and rear washers share one reservoir.
Inspect the coolant reservoir with the engine cool.
Read the brake-fluid reservoir against its MIN and MAX lines.
Measure all tire pressures monthly while the tires are cold, including the spare where fitted.
The illustrated transmitter uses a CR2032 or equivalent battery with its positive side facing up.
With the brake firmly depressed, touch the center of the key emblem to the center of the start button.
The auxiliary metal key is inside the transmitter beneath its lower cover.
Stop the powered liftgate at the desired height above halfway open, then hold its close switch for about three seconds.
After addressing a dead vehicle battery, an electrically stuck liftgate can be opened using the emergency lever behind its interior cover.
Slide each rear door child-safety lock to its locked position before closing that door.
Initialize each affected window by fully opening it, fully closing it and holding its switch up for about two seconds after closure with the ignition ON.
With ignition ON, press the overhead switch to tilt the roof or move it rearward to slide it open.
With the parking brake applied, transmission in P and engine running, adjust the seat and display.
Remove occupants and restraints, switch rear heating off if fitted, then release and support the seatback as it folds.
Support the rear backrest while pulling its release lever to adjust the angle.
Press the seat-warmer switch with ignition ON and select the desired heat using repeated presses.
Equipped front seats use built-in fans to ventilate the surface.
With ignition ON, press the heated-wheel switch.
With ignition in ACC or ON, rotate the mirror selector toward the side you want, adjust with the control and return the selector to its center position.
On the manual mirror, set the lever forward for daytime and pull it back to reduce nighttime glare.
On the Type A instrument cluster, turn the illumination knob left to dim and right to brighten.
On the instrument-cluster version described by this manual section, pressing the dashboard illumination knob changes speed units between mph and km/h.
On the Type A cluster, use INFO to display TRIP A or TRIP B and hold INFO for at least 1.5 seconds to reset that trip and its average economy.
The Type A cluster calculates average economy for each trip.
The maintenance monitor can show scheduled maintenance, tire rotation and oil-change notifications.
With ignition in ACC or OFF, pull the lighting lever to switch on the low beams temporarily.
With ignition OFF and an eligible lighting-switch position selected, pressing unlock on the transmitter can illuminate the exterior lights for about 30 seconds.
On an auto-light-equipped CX-5, AUTO allows the headlights to respond to ambient brightness with ignition ON.
Switch ignition ON and press the rear-defogger switch.
Press AUTO and choose a comfortable temperature.
The front socket requires ACC or ON; center and rear sockets can remain usable with ignition off.
The luggage board has upper and lower mounting positions.
With ignition ON and the selector out of R, press the 360° View Monitor switch to display and cycle front or side views.
Selecting R brings up the rear camera.
With ignition ON, press the parking-sensor switch.
Close the driver door, fasten the seatbelt and press AUTOHOLD.
Hold the brake pedal and pull the EPB switch up to apply the parking brake.
Use the Mi-Drive switch and check the selected mode in the instrument cluster.
Pull the interior hood-release handle, move the secondary latch to the right and raise the hood.
Fit one correctly shaped floor mat over the driver-side retention posts.
Use mild detergent, a soft sponge or cloth, and a thorough cool or lukewarm-water rinse.
Vacuum dust and sand first, wipe with suitable leather cleaner or approximately 5% mild-detergent solution, remove residue and dry gently in the shade.
Use a soft cloth dampened with lukewarm water around the rear-window heating and antenna lines.
The active-driving-display dust sheet has a delicate coating.
The equipped active driving display can be adjusted through Mazda Connect Settings.